Veilige betaling
Via iDeal, bankoverschrijving
of pinnen/contant bij ophalen
Grote voorraad
Ook apparatuur uit
het hoge segment
100% verzekerd
Dubbel verpakt en
verzekerd per PostNL

Station Master™ is unique controller on the market designed mainly for small or moderate, multiple antenna, single rotator/SteppIR or UltraBeam stations. Provides radio control, antenna switch control, band pass filters switching, selective SteppIR or UltraBeam tuning, computer controlled rotator interface, interface for automatic power amplifiers, sequencer for receiving antennas and many additional features.

Lees meer..

Beschikbaarheid: Niet op voorraad. Backorder mogelijk.

€ 372,00

Station Master™ is unique controller on the market designed mainly for small or moderate, multiple antenna, single rotator/SteppIR or UltraBeam stations. Provides radio control, antenna switch control, band pass filters switching, selective SteppIR or UltraBeam tuning, computer controlled rotator interface, interface for automatic power amplifiers, sequencer for receiving antennas and many additional features.

General:
•Programmable Antenna, BPF, Rotor and PA controller

•Twenty (20) programmable relay outputs
•Integrated level converter for transceiver computer control port
•Decodes all frequencies of connected transceiver, including 75m, 6m, VHF and dHF
•Unlimited number of custom defined frequency segments “bands”
•Single USB connection to computer
•Stand alone operation
•Internal Rotator control
•Virtual Rotators function
•Separate RX/TX antenna support
•Automatic Antenna Scan function
•Separately programmable up to 20 outputs sequencer
•Automatic power amplifier support
•Fully compatible and simple integrated with microHAM “keyers” MK, DK, CK, MKII and MK2R
•Proprietary SteppIR/UltraBeam support for automatic tunning and protection
•Hot Switch protection with user defined timing
•TX Inhibit support for Yaesu's transceivers
•Receive only antennas support
•Optical isolation from computer
•PS/2 keyboard or keypad with dual control of Station Master and microHAM “keyer”
•Integrated chokes and filters for maximum RFI immunity
•Metal/Aluminum case, powder coated and silk screened
•Free, no time limit firmware/software upgrades via Internet


Radio control:
•Integrated level converter for CI-V, FIF-232, IF-232, or RS-232

•Up to 57600 Baud with fake handshake support
•Supports most Elecraft, Icom, Kenwood, Ten-Tec, Yaesu and other radios

Antennas Control (Port A):
•Ten (10) programmable relay outputs

•Configurable power for common
◦ground
◦13.8V positive
◦external power, max. + 24V
Compatible with all remote antenna switches using common ground or positive control
Additional Antennas or BPF Control (Port B):
•Six (6) programmable relay outputs
•Configurable power for common
◦ground
◦13.8V positive
◦external power max. + 24V
•Compatible with all automatic BPF on the market


RX Antennas and TX Sequencer (Port B):
•Four (4) programmable relay outputs

•Both poles of relay contact available
•Independent settings of Lead and Tail delay for each sequencer output


Internal Rotator Control:
•Three (3) programmable relay outputs

•Both poles of relay contact available
•Configurable support for BRAKE or SPEED control
•Support for multi-turn rotators
•Support for rotators with analog (pot) or discrete (pulse) azimuth read back
•Programmable software limit switches
•Dead zone definition
•Target finding strategy selection for optimal handling
•Support for “slipping” rotators
•Four memories for most wanted azimuths
•Automatic azimuth control from logger

 Virtual Rotator Control:
•Unlimited number of antennas can be joined to Virtual Rotator

•Programmable azimuth ranges for each Virtual Rotator antenna
•Automatic azimuth control from logger
•Unlimited number of Virtual Rotators per Band


Power Amplifier Control:
•Automatic tunning for CI-V controlled automatic amplifiers (Icom PW1, Expert SPE, Tokyo Hy-Power)

•Automatic band switching for BCD controlled amplifiers (Yaesu VL-1000, FL-7000)
•Support for QSK Power Amplifiers

USB: USB 2.0 Full speed, USB 1.1 compatible
Power consumption: USB – less than 100mA
Power supply – max.1.8A at +13.8V (max. +16V)
CAT: RxD, TxD – max. 57600 Baud, RTS fixed level output max.1mA
Levels: TTL, inverted TTL, open collector bus, RS232
Serial: RS232 levels, RTS fixed level output max.1mA, up to 9600 baud
PA CI-V: open collector bus max.40mA, up to 9600 baud
All relay outputs: 30VDC, 48VAC, max.2A
External PORT A power: max. +24V/1.3A
External PORT B power: max. +24V/1.3A
PS/2 consumption: max. 200mA at +5V
Rotator analog input: 10K ohm, max. +/-12V
Rotator pulse input: active when grounded, max.+24V/5mA
Rotator reference output: 9V, max.20mA
PA Keying output: open collector, max.+45V/800mA
PA Keying input: active when grounded, max.+24V/5mA
PA ON/OFF control: +12V, max.100mA
Dimensions: W 230mm (9") x H 44mm (1.73") x D 160mm (6.3")


1.POWER
LED lights when +13.8V is applied (power switch on).

2.ALARM
LED lights when “ALARM” condition happens, transmission is allowed.
LED flashes when “ALARM” condition happens, transmission is inhibited.

3.READY
LED lights when transmission is allowed.
LED flashes when transmit condition has been changed and will be applied on next transmission cycle.

4.BUSY
LED lights when “BUSY” condition happens, transmission is allowed.
LED flashes when “BUSY” condition happens, transmission is inhibited.

5.FUNC/MENU
Short press and release opens “Function” list.
Press and hold for more than one second opens “Menu” list.

6.ENCODER
Rotary encoder with push button. Function vary on configuration and antenna selection.

7.<-/YES
Button for browsing between available antennas backward and menu navigation.

8.->/NO
Button for browsing between available antennas forward and menus navigation.

 

1.DC 13.8V
Power Supply - 2.1 x 5.5 mm coaxial jack, center is positive (+).

2.iLINK
MiniDIN-6 for connection with microHAM “keyer” or function expansion module.

3.USB
USB B connector for computer connection.
Standard USB A-B cable.

4.SERIAL
RS232 level serial port.
DB9 female jack.
See Appendix “Connectors” for details.

5.PA
DB15 female jack for connection with Power Amplifier.
compatible with microHAM “CAT” cables
See Appendix “Connectors” for details.

6.PORT A
DB25 female jack for antenna switch connection.
See Appendix “Connectors” for details.

7.PS/2
MiniDIN6 for PS/2 keyboard or PS/2 keypad.

8.INHIBIT
Power inhibit output for Yaesu's transceivers.
RCA jack  TIP - Signal  SHELL - GND 

9.CAT
4 pole 3.5mm phono jack for transceiver control. Compatible with microHAM “CAT” cables.

10.GND
Terminal for connection to station ground.

11.iLINK
MiniDIN-6 for connection with microHAM “keyer” or function expansion module.

12.POWER
Power Switch.

13.ROTOR
DB15 female jack for connection with Antenna Rotator.
See Appendix “Connectors” for details.

14.PORT B
DB25 female jack for antenna switch, BPF and/or sequencer connection.
See Appendix “Connectors” for details.

15.PTTIN
PTT Input for connection with PTT output from transceiver or PAPTT output from microHAM “keyer”. Active when closed to ground.
RCA jack TIP - Signal   SHELL – GND

Schrijf uw eigen review
  1 ster 2 sterren 3 sterren 4 sterren 5 sterren
Ons
Product